M8Q 5883 - GPS und Kompass Modul

Matek Ublox SAM GPS und Kompass Modul M8Q-5883 INAV - Übersichtsseite

Link zum Premium-Modellbau Shop

https://www.premium-modellbau.de/matek-ublox-sam-gps-und-kompass-modul-m8q-5883-inavwww.premium-modellbau.de

Matek Ublox SAM GPS und Kompass Modul M8Q-5883 INAV im Premium-Modellbau Shop

Matek M8Q-5883 Anleitung

Montage und Inbetriebnahme:

Bitte beachten Sie unbedingt den angegebenen Spannungsbereich für das jeweilige Board. Eine zu hohe Spannung wird die angeschlossenen Komponenten beschädigen.

Achten Sie beim Anschluss der Kabel am Akku immer auf korrekte Polung (und isolieren Sie die Leitungen entsprechend mit Schrumpfschlauch.

Matek Ublox GPS und Kompass Modul zur Nutzung mit FPV Flightcontrollern (Betaflight, INAV).

Gewicht: ca. 7g

Abmessungen: 20x 20 mm

https://www.premium-modellbau.de/media/image/9b/a8/49/GPS-M8Q-5883-2.jpg

Features

• 72-channel u-blox M8 engine GPS L1C/A, SBAS L1C/A, QZSS L1C/A, QZSS L1 SAIF, GLONASS L1OF, Galileo E1B/C

• On-board Ultra low noise 3.3V voltage regulator and RF filter for noise blocking

• Features an additional front-end LNA for optimized performance and a front-end SAW filter for increased jamming immunity

• Build-in embedded GNSS patch antenna, low power consumption

• The 15 x 15 mm patch antenna provides the best compromise between the performance of a Right Hand Circular Polarized (RHCP) antenna and a small size to be integrated in any design.

• Magnetic sensor QMC5883L integrated

• Max navigation update rate Single GNSS up to 18 Hz 2 Concurrent GNSS(GPS & GLONASS) up to 10 Hz

• Horizontal position accuracy(GPS & GLONASS) 2.5 m CEP

• Velocity accuracy 0.05m/s

• Cold start 26 s Aided cold starts: 2 s Hot start 1 s

• Sensitivity Tracking & Navigation: –165 dBm Reacquisition: –158 dBm Cold start: –146 dBm Hot start: –155 dBm

• Input voltage range: 4~6V

• Uart (Tx,Rx) interface for GPS SAM-M8Q

• I2C (DA,CL) interface for Compass QMC5883L

• Battery for HOT module start

• Power LED(Red) & Time pulse LED(Blue)

• Dimensions: L20 x W20 x H10 mm

• Weight: 7 gram

• Supported by INAV/Betaflight/Ardupilot, ect.

Including

• M8Q-5883 module, 1 pc

• SH1.0-6P 20cm silicon wire, 1 pc

• Transparent PVC Heat-shrink tube

Tips

• GPS, GLONASS, SBAS, QZSS are enabled by default

• Blue PPS LED blinking(1Hz) means 3D fixed

• update rate 1Hz & baudrate 9600 default

• Baud 9600~115200 supported by INAV/BF/Ardupilot

• update rate 5Hz with INAV UBLOX Protocol

• update rate 10Hz with INAV UBLOX7 Protocol

• Compass Alignment(Arrow forward): INAV/BF: CW 270° Flip Ardupilot/Mission Planner: Rotation None

• BF doesn’t support GPS position hold and RTH, GPS Rescue mode is supported by BF3.5 or last.

• No need compass for Fixed wings with INAV firmware

• The scratches on ceramic antenna are the result of tuning the antenna by ublox.